LeftyBassist.com
http://leftybassist.com/

ISO anodized gold P bass pickguard
http://leftybassist.com/viewtopic.php?f=12&t=10339		 Page 1 of 1
Author:  leftybassatl [ April 11th, 2020, 8:16 pm ]
Post subject:  ISO anodized gold P bass pickguard
These are pretty tough to find at the moment. Let me know if you have one you're willing to let go. Looking to spruce up my sunburst '78.
Author:  bobjones2260 [ April 14th, 2020, 6:50 am ]
Post subject:  Re: ISO anodized gold P bass pickguard
I only have a Gold Plastic Pickguard that I got but never used as it does not even come close to the feel.
Author:  leftybassatl [ April 14th, 2020, 3:17 pm ]
Post subject:  Re: ISO anodized gold P bass pickguard
Researching all over and found myself right back here- Great thread on this topic from 2013- viewtopic.php?f=3&t=4890

I think I will consider the flipped approach (seems to have worked beautifully for sblueplanet!), or have tone guard make one for me if that doesn't work. Thanks everyone!
Author:  leftybassatl [ April 14th, 2020, 3:17 pm ]
Post subject:  Re: ISO anodized gold P bass pickguard
bobjones2260 wrote:
I only have a Gold Plastic Pickguard that I got but never used as it does not even come close to the feel.


Good to know, I was considering this approach too. Thanks for the insight.
Author:  ch willie [ April 14th, 2020, 4:16 pm ]
Post subject:  Re: ISO anodized gold P bass pickguard
I want an anodized for my white P Bass and maybe one for my sunburst Jazz Bass.

I might check out these guys

http://www.tone-guard.com
Author:  paulo [ April 14th, 2020, 5:33 pm ]
Post subject:  Re: ISO anodized gold P bass pickguard
You could also just buy a righty and flip it.
Most of them are painted in the back in the pot area for shielding but there's a lot of them that are nice and clean, just need to ask the seller to send a picture of the back side.
Then you'll need to counter sink the screw holes.
I done that in at least 3 pickguards and all of them came out great.
Author:  gravesbass [ May 16th, 2020, 9:07 am ]
Post subject:  Re: ISO anodized gold P bass pickguard
@ leftybassati

Ask the guy to see the back of it. I have one that doesn't have anything on it. Some have shielding tape.

Here is one on talkbass. You can flip it and as Paulo said you'll need to counter sink the screw holes.

https://www.talkbass.com/threads/fender ... d.1461988/

good luck!
Author:  crescenze [ May 16th, 2020, 9:37 am ]
Post subject:  Re: ISO anodized gold P bass pickguard
You may have already considered this, but the original anodized pick guards have 10 holes so they wouldn't be a direct replacement on your 78. If it's a player drilling extra holes may not be an issue. Not sure if there are any aftermarket or RI 13 hole guards produced that would be a exact fit.
Author:  paulo [ October 7th, 2020, 2:33 pm ]
Post subject:  Re: ISO anodized gold P bass pickguard
https://www.talkbass.com/threads/fender ... e.1484528/
This looks pretty clean on the back side and could be used as lefty. Pics of the back side on the listing.
Author:  Psycho Ward [ October 8th, 2020, 6:41 am ]
Post subject:  Re: ISO anodized gold P bass pickguard
The top of a right handed one is slightly beveled around the edges, at least the one that was on one of my basses. I didn't bother me much, but there was a ledge.
Author:  LeftyClover [ October 18th, 2020, 12:55 pm ]
Post subject:  Re: ISO anodized gold P bass pickguard
For my 58P reissue I ordered one at WD Custom. They had one lefty in stock at the time. Including non-anodized rings around the potmeter holes so these would make proper contact (as anodized aluminium is a good isolator). Highly recommended!
Image
Page 1 of 1 All times are UTC - 8 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/